This uses a struct to cache the block size for aligned reads/writes,
to avoid repeated ioctl(BLKSSZGET) calls.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Avoid possibly using stale data in bitmap and misc area of superblock.
In addition, remove superfluous memsets already covered by memset of
full superblock.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use a #define rather than calculate the size of the superblock buffer
on every allocation.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We just calculated the pointer to the bitmap, so use it instead of
recalculating.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The current 1024 byte limit on 1.x superblocks limits us to
384 devices. Sometimes people want more.
The kernel is already prepared for superblocks up to 4K,
so enable that in mdadm allowing up to
(4096-256)/2 == 1920
devices (active plus spare).
Signed-off-by: NeilBrown <neilb@suse.de>
In addition remove attempt to print an error message if
write_init_super() fails, as this is handled in the various
write_init_super() functions. This avoids a segfault on error.
Reported by Jim Meyering in
https://bugzilla.redhat.com/show_bug.cgi?id=795461
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes super[01].c properly align buffers used for the bitmap
using posix_memalign() to make sure the writes don't fail in case the
bitmap is opened using O_DIRECT.
This is based on https://bugzilla.redhat.com/show_bug.cgi?id=789898
and an initial patch by Alexander Murashkin.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A recently change to write_bitmap1 meant awrite would sometimes
write from a non-aligned buffer which of course break.
So change awrite (and aread) to always use their own aligned
buffer to ensure safety.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
when deciding whether the array is clean or dirty, compare
sb->resync_offset against MaxSector and not against sb->size
With RAID6 resyncing and subsequent drive failures, it is possible to
reach the case, in which sb->resync_offset==sb->size. This happens
when resync is aborted due to drive failures, and immediately a
rebuild of a spare starts. In this case, mdadm was considered the
array as clean, while kernel was considering the array as dirty. It is
better for mdadm also to consider the array as dirty in this case.
Signed-off-by: NeilBrown <neilb@suse.de>
Adding a bitmap via ioctl can only add it at a fixed location.
That location is not suitable for 4K-block devices.
So allow setting the bitmap location via sysfs if kernel supports it
and aim to always use 4K alignments.
Signed-off-by: NeilBrown <neilb@suse.de>
When container is assembled while reshape is active on one of its member
whole container can be required to be blocked from monitoring.
For such purpose field recovery blocked is added to mdinfo structure.
When metadata handler finds active reshape in container it should set
recovery_blocked field to disable whole container monitoring during
reshape.
For arrays that doesn't use containers, recovery_blocked field
has the same value as reshape_active field e.g. super0/1.
In fact,recovery is blocked during reshape for such arrays.
For ddf, metadata handler doesn't set reshape_active field,
so recovery_blocked is not set also.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If you create a two drive raid1 array with one device writemostly, then
fail the readwrite drive, when you add a new device, it will get the
writemostly bit copied out of the remaining device's superblock into
it's own. You can then remove the new drive and readd it as readwrite,
which will work for the readd, but it leaves the stale WriteMostly1 bit
in devflags resulting in the device going back to writemostly on the
next assembly.
The fix is to make sure that A) when we readd a device and we might have
filled the st->sb info from a running device instead of the device being
readded, then clear/set the WriteMostly1 bit in the super1 struct in
addition to setting the disk state (ditto for super0, but slightly
different mechanism) and B) when adding a clean device to an array (when
we most certainly did copy the superblock info from an existing device),
then clear any writemostly bits.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some code currently clears 'info' before calling getinfo_super,
some code doesn't.
To be consistent, change it so no caller ever clears 'info',
but ever getinfo_super function must clear it.
Note that ->raid_disk may be meaningful if that 'map' is passed
non-NULL. In that case it is copied out before the structure
is zeroed.
Signed-off-by: NeilBrown <neilb@suse.de>
As homehost defaults to the system name it is not possible to specify
a NULL homehost.
This patch restored this ability with either --homehost="" or
--homehost="<none>".
This allows the creation of v1.x arrays without a "hostname:"
prefix in the name.
Signed-off-by: NeilBrown <neilb@suse.de>
the new code for defaulting chunksizes didn't work quite right
- default was set to late in super1/super0/ddf
- defaults would over-ride values of '0' imposed by some levels
- default value wasn't applied to size properly.
Signed-off-by: NeilBrown <neilb@suse.de>
When chunk size is not set from command line we need to guess it
depending on metadata given on command line or found on listed devices.
Validate_geometry sets the default for it's metadata if chunk is not set.
For external metadata chunk is set only when creating in a container.
For imsm validate_geometry_imsm_orom is responsible for finding default
chunk depending on container metadata loaded. Container will already know
which controller it is attached to, and have this controllers orom
available.
do_default_chunk indicates that we need to find default chunk and
if validate_geometry fails for some metadata it tells us to reset chunk
that may have been set.
Current solution would set default chunk correctly for imsm only if
container device was given on command line. With the list of devices
chunk was always set to 512.
Signed-off-by: Anna Czarnowska <anna.czarnowska@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we force-assemble an array which is in the middle of a reshape,
we should repeat the reshape of any parts that aren't recorded in
the oldest superblock.
This is unlikely to make a significant difference, but could make
a small difference, and is safer.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that a 'supertype' container more information, the simplistic
copying of 'st' into 'refst' is incorrect and results in closing
some fds when load_super1(refst) calls free_super().
So do it more correctly using dup_super.
Reported-by: "Labun, Marcin" <Marcin.Labun@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We previously closed all 'fds' associated with an array in
write_init_super .. sometimes, and sometimes at bad times.
This isn't neat and free_super is a better place to close them.
So make sure free_super always closes the fds that the metadata
manager kept hold of, and stop closing them in write_init_super.
Also add a few more calls to free_super to make sure they really do
get closed.
Reported-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It makes more sense to test for container_dev than for subarray
for several places in Create where it then uses container_dev.
This allows us to subsequently remove subarray.
Signed-off-by: NeilBrown <neilb@suse.de>
This allows the info for a single array to be extracted,
so we don't have to write it into st->subarray.
For consistency, implement container_content for super0 and super1,
to just return the mdinfo for the single array.
Signed-off-by: NeilBrown <neilb@suse.de>
To accurately detect when an array has been split and is now being
recombined, we need to track which other devices each thinks is
working.
We should never include a device in an array if it thinks that the
primary device has failed.
This patch just allows get_info_super to return a list of devices
and whether they are thought to be working or not.
Signed-off-by: NeilBrown <neilb@suse.de>
If an --update is requested by the relevant metadata doesn't
understand it, print a useful message rather than silently ignoring
the issue.
Signed-off-by: NeilBrown <neilb@suse.de>
This code is wrong is several ways, and failed on big-endian machines.
Put in correct endian coversions: 'want' is cpu-order, dev_roles[] is little-endian,
16 bit.
Reported-by: Doug Nazar <nazard.michi@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This number isn't meaningful for RAID0 as a different amount of space
might be used from each device.
It isn't meaningful for linear either, but already was not reported
for linear.
Detail doesn't report it either.
So make --examine not report it.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Mario 'BitKoenig' Holbe <Mario.Holbe@TU-Ilmenau.DE>
This commit introduces DEFAULT_OLD_METADATA as a preprocessor
definition. If defined, it causes mdadm to assume metadata version 0.9
as default. If not defined, version 1.x (currently 1.2) is used as
default.
The man page mdadm.8 is also modified to reflect the chosen default.
The selftests will not work if the old default is chosen.
This patch was requested by Debian so they could distribute a current
mdadm together with boot loaders that only understand 0.90 metadata
for md-raid.
Preferred usage is simply
make DEFAULT_OLD_METADATA=yes
Signed-off-by: martin f. krafft <madduck@debian.org>
Signed-off-by: NeilBrown <neilb@suse.de>
If the metadata is an empty string, it means the array in question
does not use metadata. This comes from sysfs_read finding "none" in
"metadata_version", then super_by_fd noticing the vers == -1, and so
just using the ->text_version (which is empty).
In this case we want to use the super0 metadata handler routines
because that is what we always used to do before
commit 7d5c3964cc
And that commit was wrong because "" doesn't mean "default" and so
should not have been changed at the same time.
Reported-by: martin f. krafft <madduck@debian.org>
Signed-off-by: NeilBrown <neilb@suse.de>
For 1.1 and 1.2 metadata where data_offset is not zero,
it is important to align the data_offset to underlying
block size.
We don't currently have access to the particular device
in avail_size so just try to force to a 1Meg boundary.
Also default 1.x metadata to 1.2 as documented.
Signed-off-by: NeilBrown <neilb@suse.de>
Change default - again, sorry.
v1.1 causes problems as the conflicts with a boot sector, whether on
the whole device or in a partition. I guess the rule is they you
aren't allowed to use the first sector in general.
v1.2 is mostly just as good and avoid boot-sector problems so default
to that instead.
Signed-off-by: NeilBrown <neilb@suse.de>
Some devices have 4K sector sizes. So try to align the bitmap
on a 4K boundary.
This isn't possible when hot-adding a bitmap, but will be once
we add support for configuring the bitmap via sysfs.
Signed-off-by: NeilBrown <neilb@suse.de>
1.x metadata allows a device to be a member of the array while it
is still recoverying. So it is a working member, but is not
completely in-sync.
mdadm/assemble does not understand this distinction and assumes that a
work member is fully in-sync for the purpose of determining if there
are enough in-sync devices for the array to be functional.
So collect the 'recovery_start' value from the metadata and use it in
assemble when determining how useful a given device is.
Reported-by: Mikael Abrahamsson <swmike@swm.pp.se>
Signed-off-by: NeilBrown <neilb@suse.de>
Replace occurrences of ~0ULL to make it clear we are talking about maximal
resync/recovery position.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- When --kill-superblock is used with --metadata, find every
different superblock if there are several and kill them all.
- When creating a new array, kill off any old metadata. The code
to do this was already present but has become broken over time.
Signed-off-by: NeilBrown <neilb@suse.de>
->validate_geometry is called to validate overall parameters,
and to validate each individual device.
If it ever fails, it needs to report the reason, as common code
cannot possible know.
Signed-off-by: NeilBrown <neilb@suse.de>
Jes Sorensen
NeilBrown
Alexander Lyakas
Adam Kwolek
Doug Ledford
Scott Schaefer
Luca Berra
Czarnowska, Anna
martin f. krafft
Dan Williams