87 lines
2.2 KiB
Plaintext
87 lines
2.2 KiB
Plaintext
# Test suggested by Albert Pauw: Create, fail one disk, have mdmon
|
|
# activate the spare,
|
|
# then run create again. Shouldn't use the failed disk for Create,
|
|
. tests/env-ddf-template
|
|
|
|
tmp=$(mktemp /tmp/mdtest-XXXXXX)
|
|
rm -f $tmp
|
|
|
|
mdadm --zero-superblock $dev8 $dev9 $dev10 $dev11 $dev12 $dev13
|
|
mdadm -CR $container -e ddf -l container -n 5 $dev8 $dev9 $dev10 $dev11 $dev12
|
|
|
|
mdadm -CR $member0 -l raid1 -n 2 $container
|
|
#$dir/mdadm -CR $member0 -l raid1 -n 2 $container >/tmp/mdmon.txt 2>&1
|
|
|
|
check wait
|
|
|
|
set -- $(get_raiddisks $member0)
|
|
fail0=$1
|
|
mdadm --fail $member0 $fail0
|
|
|
|
# To make sure the spare is activated, we may have to sleep
|
|
# 2s has always been enough for me
|
|
sleep 2
|
|
check wait
|
|
|
|
# This test can succeed both ways - if spare was activated
|
|
# before new array was created, we see only member 0.
|
|
# otherwise, we see both, adn member0 is degraded because the
|
|
# new array grabbed the spare
|
|
# which case occurs depends on the sleep time above.
|
|
ret=0
|
|
if mdadm -CR $member1 -l raid5 -n 3 $container; then
|
|
# Creation successful - must have been quicker than spare activation
|
|
|
|
check wait
|
|
set -- $(get_raiddisks $member1)
|
|
if [ $1 = $fail0 -o $2 = $fail0 -o $3 = $fail0 ]; then
|
|
echo ERROR: $member1 must not contain $fail0: $@
|
|
ret=1
|
|
fi
|
|
d1=$1
|
|
mdadm -E $d1 >$tmp
|
|
if ! grep -q 'state\[1\] : Optimal, Consistent' $tmp; then
|
|
echo ERROR: member 1 should be optimal in meta data
|
|
ret=1
|
|
fi
|
|
state0=Degraded
|
|
else
|
|
# Creation unsuccessful - spare was used for member 0
|
|
state0=Optimal
|
|
fi
|
|
|
|
# need to delay a little bit, sometimes the meta data aren't
|
|
# up-to-date yet
|
|
sleep 0.5
|
|
set -- $(get_raiddisks $member0)
|
|
if [ $1 = $fail0 -o $2 = $fail0 ]; then
|
|
echo ERROR: $member0 must not contain $fail0: $@
|
|
ret=1
|
|
fi
|
|
d0=$1
|
|
|
|
[ -f $tmp ] || mdadm -E $d0 >$tmp
|
|
|
|
if ! grep -q 'state\[0\] : '$state0', Consistent' $tmp; then
|
|
echo ERROR: member 0 should be $state0 in meta data
|
|
ret=1
|
|
fi
|
|
if ! grep -q 'Offline, Failed' $tmp; then
|
|
echo ERROR: Failed disk expected in meta data
|
|
ret=1
|
|
fi
|
|
if [ $ret -eq 1 ]; then
|
|
cat /proc/mdstat
|
|
mdadm -E $d0
|
|
mdadm -E $d1
|
|
mdadm -E $fail0
|
|
fi
|
|
|
|
[ -f /tmp/mdmon.txt ] && {
|
|
cat /tmp/mdmon.txt
|
|
rm -f /tmp/mdmon.txt
|
|
}
|
|
|
|
rm -f $tmp
|
|
[ $ret -eq 0 ]
|