A recent change means that devices smaller than
1Gig no longer have 1Meg wasted at the start.
So we must adjust some sizes again.
Signed-off-by: NeilBrown <neilb@suse.de>
We do not check if requested size of expansion is larger than maximum
available size now. If it is larger the output message is a bit misleading,
for example:
mdadm: Cannot set size on array members.
mdadm: Cannot set device size for /dev/md/vol: Device or resource busy
Now we check if requested size of expansion is larger than maximum
available size and the appropriate output message was added.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we are looking for a candidate disk to bump up the event count,
we consider only disks that have recovery_start==MaxSector.
However, after we find one such disk, we agree to accept more disks
having same event count, regardless of their recovery_start.
Be consistent and don't accept disks with a valid recovery_start at all.
Signed-off-by: NeilBrown <neilb@suse.de>
This is most likely to happen if the array has been stopped,
in which case the error is pointless.
Reported-by: Patrik Horník <patrik@dsl.sk>
Signed-off-by: NeilBrown <neilb@suse.de>
I think there was some confusion about what --layout=preserve
actually means, but in any case it wasn't doing what the man
page says it should.
So add some case analysis and make sure it does the right thing,
or complains if it cannot.
Reported-by: Patrik Horník <patrik@dsl.sk>
Signed-off-by: NeilBrown <neilb@suse.de>
While it is nice to set a high data_offset to leave plenty of head
room it is much more important to leave enough space to allow
of the data of the array.
So after we check that sb->size is still available, only reduce the
'reserved', don't increase it.
This fixes a bug where --adding a spare fails because it does not have
enough space in it.
Reported-by: nowhere <nowhere@hakkenden.ath.cx>
Signed-off-by: NeilBrown <neilb@suse.de>
Use closedir() on dirp from opendir() to avoid resource leaking.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This should be harmless, but lets be consistent and not try to close a
negative file descripter.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
With different amounts of space being reserved for metadata
it is hard for the script to know how big the array should be.
So allow a bit of slack.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that /run seems to be a good standard, make that
the default for storing various run-time files, rather than
/var/run or /dev/.mdadm.
Signed-off-by: NeilBrown <neilb@suse.de>
Spare superblock doesn't depend on other spares in container.
When loading container metadata thunderdome
may pick a small disk for the champion. This will result in incorrect
interpretation of sizes of other disks in container when joint superblock
is returned. If any disk in container has the 2TB attribute set, the result
must have it set too.
Signed-off-by: Anna Czarnowska <anna.czarnowska@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
mdinfo->bitmap_offset is a signed long and needs to be treated as
such when passed to the kernel.
This resolves the problem with adding internal bitmaps to a 1.0 array.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
fbdef49811 incorrectly tried to fix sign
extension of the bitmap offset. However mdinfo->bitmap_offset is a u32
and needs to be converted to a 32 bit signed integer before the sign
extension.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Setting "sync_action" to "idle" while extending size of raid0 array
is racy and sometimes fails.
"sync_action" should be set to "frozen" instead.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If system is rebooted during rebuild, md driver changes sync_action
from 'recover' to 'idle' (during stopping all md devices).
If mdmon is still running then, it detects the change of sync_action state,
finishes rebuild and writes metadata to disks. After computer's restart
the RAID volume is in Normal state in OROM and rebuild seems to be finished.
After system's start-up RAID volume is in auto-read-only state
and metadata is in Dirty state. Rebuild seems to be finished but it is not.
Data is inconsistent (out-of-sync).
When mdmon detects the change of sync_action from 'recover' to 'idle',
it has to check if rebuild is really finished. Appropriate test was added.
Now mdmon examines each volume's member if it is being rebuilt.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The restriction that --add was not allowed on a device which
looked like a recent member of an array was overly harsh.
The real requirement was to avoid using --add when the array had
failed, and the device being added might contain necessary
information which can only be incorporated by stopping and
re-assembling with --force.
So change the test to reflect the need.
Reported-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Both --detail and --monitor can report the names of member
devices on an array, and do so by searching /dev and finding
the shortest name that matches.
If
--prefer=foo
is given, they will instead prefer a name that contain /foo/.
So
mdadm --detail /dev/md0 --prefer=by-path
will list the component devices via their /dev/disk/by-path/xxx
names.
Signed-off-by: NeilBrown <neilb@suse.de>
When we can for devices using GET_DISK_INFO we currently
limit to 1024. But some arrays can have more than this.
So raise it to 4096 and make the constant a #define.
Signed-off-by: NeilBrown <neilb@suse.de>
When mdadm is compiled using e.g. 'everything' option, mdassemble
compilation is broken.
Change code to enable mdassemble compilation.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When arrays using external metadata are assembled, and one of array
in container is under reshape, second array will remain in read only
state (not auto read only). It is caused by array fact that array
is frozen and mdmon doesn't has opportunity to switch array in r/w mode.
Freezing not reshaped array just after it is being assembled allows mdmon
to enable it for writing.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Size change is possible as standalone change only. To make sure size change
is not requested pass '-1' as size parameter.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Put currently existing code for alignment correction in to function
imsm_component_size_aligment_check() and use it for align component size
to chunk size during volume size expansion operation.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add support for setting max size for size change operation using
imsm_get_free_size() function for computing maximum available space.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add function imsm_imsm_get_free_size() using part of code from function
reserve_space().
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some setting size error cases were not detected.
When error occurs, stop setting new size action and rollback metadata
changes.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When reshape_super() updates metadata with new size, due to some metadata
limitations saved value can be different than requested value by user.
Update size (read it from metadata) for setting it in md.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For raid0, takeover operation is required for size change.
Add takeover to degraded raid4 before size change and back to raid0 after.
Array information has to be read again from md after takeover.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add metadata rollback specific code for imsm.
Let reshape_super() ability to differentiate metadata apply and rollback
actions.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Function reshape_super() guards metadata changes.
It is used to apply changes rollback in error case also.
As change (apply and rollback) can be not bi-directional reshape_super()
has to know if current action is metadata change that should be guarded
using metadata restrictions, or this is metadata rollback change
executed due to error occurrence.
In second case change has to be unconditional.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For external metatdata ioctl doesn't set new size. Set new size using sysfs.
Put code for size change in to function to re-use the same code as during
On-line Capacity Expansion
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add new meatdata update type imsm_update_size_change, and update metadata
for volume size expansion operation.
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Patch adds ability to function imsm_analyze_change() for:
1. Detect size change request for volume operation.
2. Check and correct size for change.
3. Set new change kind to CH_ARRAY_SIZE
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Function imsm_num_data_members() returns wrong value for raid 1 and 10.
It returns all data member but it should return number of unique data
members (excluding mirror devices)
Signed-off-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Display maximum volumes per array and per controller
in --detail-platform command.
Signed-off-by: Marcin Labun <marcin.labun@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
manpage for mdadm(8) contains typo - missing "d" at the end of "describe" word.
Signed-off-by: Roman Ovchinnikov <coolthecold@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The kernel is growing the ability to avoid the need for a
backup file during reshape by being able to change the data offset.
For this to be useful we need plenty of free space before the
data so the data offset can be reduced.
So for v1.1 and v1.2 metadata make the default data_offset much
larger. Aim for 128Meg, but keep a power of 2 and don't use more
than 0.1% of each device.
Don't change v1.0 as that is used when the data_offset is required to
be zero.
Signed-off-by: NeilBrown <neilb@suse.de>
As the bitmap can be before the superblock, bitmap_offset is signed.
But some of the code didn't honour that :-(
Signed-off-by: NeilBrown <neilb@suse.de>
It isn't sufficient to use '0' for 'error' as well will
later have fields that can validly be '0'.
So return "-1" on error.
Also fix parsing of --bitmap_check so that '0' is treated
as an error: we don't support 512B anyway.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch ensures metadata attribute is set correctly also for spares.
Signed-off-by: Anna Czarnowska <anna.czarnowska@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Creation of a container using disks over 2TB should be allowed only when orom supports large disks
Signed-off-by: Anna Czarnowska <anna.czarnowska@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown
Lukasz Dorau
Alexander Lyakas
Jes Sorensen
Czarnowska, Anna
Adam Kwolek
Labun, Marcin
CoolCold