When the array is stopped during a critical section, we sometimes
erase the backup, which is bad.
This happens when 'completed' is zero.
This can happen easily when 'stop' freezes reshape.
So try to be more careful and check 'reshape_position'.
Signed-off-by: NeilBrown <neilb@suse.de>
Appologies if this is the wrong mailing list for this patch.
This is a very small patch for the manual page for the mdadm utility.
Thanks,
Andrew
Signed-off-by: NeilBrown <neilb@suse.de>
Function add_new_arrays() expects that function get_md_name() should
return pointer to devname, but also get_md_name() may return NULL. So
check the pointer before use it in add_new_arrays().
Signed-off-by: Sergey Vidishev <sergeyv@yandex-team.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
sometimes these can get left around, and udev can be looking
at them at awkward times so they don't disappear.
So be forceful.
Signed-off-by: NeilBrown <neilb@suse.de>
Some old kernels set 'completed' to '0' too soon.
But modern kernels don't.
And when 'mdadm --stop' freezes and resume the grow,
'completed' goes back to zero briefly, which can confuse this
logic.
So only think '0' might be wrong from an old kernel when
the reshape has gone idle.
Signed-off-by: NeilBrown <neilb@suse.de>
EBUSY can be returned if something has recently happened
to cause md to want to check if recovery is needed, but hasn't
had a chance yet.
This can easily happen in testing.
So retry a few times in that case.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ use correct data-offset for cmp - that has changed.
2/ flushbufs on the block device before reading to avoid cache issues
Signed-off-by: NeilBrown <neilb@suse.de>
I don't really know why this is needed, but there is a delay
between the reshape finishing and the level/etc changing.
So add some sleeps.
Signed-off-by: NeilBrown <neilb@suse.de>
The current sleep/wait doesn't seem long enough,
particularly when two arrays are being reshaped in the one
container.
So wait a bit more...
Signed-off-by: NeilBrown <neilb@suse.de>
We might be trying to set_new_data_offset() for RAID10, when it is
a necessary requirement, or for RAID5 where it is optional.
In the latter case, a message about metadata versions is no helpful.
Signed-off-by: NeilBrown <neilb@suse.de>
avail_size1 requires ->sb, so we must only call it if ->sb
was loaded.
If ->sb wasn't loaded, then we are only proceding on the basis that
the kernel might be able to work something out - we don't need to
do any tests on size.
Reported-by: Christoffer Hammarström <christoffer.hammarstrom@linuxgods.com>
Signed-off-by: NeilBrown <neilb@suse.de>
URL: https://bugs.debian.org/784874
This can report non-zero if there was nothing to do,
and that isn't really an error.
If the array doesn't get started, something else
will complain.
Signed-off-by: NeilBrown <neilb@suse.de>
This is a very corner-case, but the self-tests tripped on it,
and it makes sense not to trust the uuid when it is being changed.
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit 30bee0201, the anchor is updated from the active
DDF header. This requires fixing the header type before the
anchor is written.
The LSI Software RAID code will reject DDF meta data with wrong
anchor type and will erase all meta data when it encounters
such a broken anchor. Thus starting Linux md once on a system
with LSI RAID BIOS may cause the meta data to get destroyed.
Signed-off-by: NeilBrown <neilb@suse.de>
"--wait" will return non-zero status if it didn't need to wait.
This is no a reason to fail a test.
So ignore the return status from those commands.
Signed-off-by: NeilBrown <neilb@suse.de>
We 'active_disks' does not count spares, so if array is rebuilding,
this will not necessarily find all devices, so may report an array
as failed when it isn't.
Counting up to nr_disks is better.
Signed-off-by: NeilBrown <neilb@suse.de>
Active arrays with IMSM metadata are counted per hba so far.
This is bad due to new functionality of orom shared between multiple
controllers i.e. more arrays can be created than is supported by orom.
This patch changes the way of counting arrays, so the result will be
sum of arrays under every hba supported by specific orom.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Normally we do not "force"-assemble devices which are in the
middle of recovery, as they are unlikely to have useful data.
However, when a reshape increases the number of devices,
the newly added devices appear to be recovering because they
do not have complete data on them yet, but then they aren't expected
to until the reshape completes.
So in this case, it can be appropriate to force-assemble them.
Reported-by: "Jonathan Harker (Jesusaurus)" <jesusaurus@gentlydownthe.net>
Signed-off-by: NeilBrown <neilb@suse.de>
If the parity device of a RAID4 is missing, then there is no immediate
risk to data. So it doesn't matter if the array is dirty or not.
This can be important when reshaping a RAID0, and is a much better
solution that that in the resent-reverted.
b720636a58
Reported-by: "Jonathan Harker (Jesusaurus)" <jesusaurus@gentlydownthe.net>
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit b720636a58.
As it said, this was a hack. It causes problems when trying to
--force assemble a RAID4. There is a better way.
Reported-by: "Jonathan Harker (Jesusaurus)" <jesusaurus@gentlydownthe.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Since we introduced replacement devices, the 'i' used in
start_array() is twice the slot number.
So we need to adjust when printing.
Signed-off-by: NeilBrown <neilb@suse.de>
"Wrong-Level" is a reason, not a component device, so it should
start with a space to indiciate this to alert().
Signed-off-by: NeilBrown <neilb@suse.de>
"alert" treats the "disc" arg differently if it starts with a space.
At least it does for sending email. It doesn't for writing to syslog.
Make this consistent and obey the 'space protocol' when writing to
syslog.
Signed-off-by: NeilBrown <neilb@suse.de>
Kernels between
c6563a8c38fde3c1c7fc925a v3.5-rc1~110^2~53
and
b5254dd5fdd9abcacadb5101 v3.5-rc1~110^2~51
allow new_offset to be set, but don't then allow a RAID5
to be reshaped to change that offset.
Due to selective backports, this includes the SLES11-SP3 kernel.
It is quite easy to handle this case in mdadm, so we do.
Specifically: if the reshape with data-offset fails with EINVAL,
abort the data-offset change and try the "old" way.
Signed-off-by: NeilBrown <neilb@suse.de>
"mdadm -If" - triggered from udev rules when disk is removed from OS -
tries to set array in auto-read-only mode. This can interrupt rebuild
process which is started automatically, e.g. if array is mounted and
spare disk is available (I/O error is detected faster than removing
failed disk by mdadm).
This patch prevents "mdadm -If" from setting array into "auto-read-only",
by requiring exclusive open to succeed.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Devices list in PCI Data Structure is supported only in
3 and above revision. Make sure that this is checked.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Replaced oroms array with list, add_orom() now only appends to this list
and add_orom_device_id() only appends devid_list node to an orom_entry.
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
static checkers complain about that.
So change the code to use 'fstat', as we really don't want
to see an error here..
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The buffer passed on to readlink() needs to contain space for the
terminating \0. See 'man 3 readlink' for details.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It is best to keep strings all together so that they
are easier to search for in the source code.
If a string is so long that it looks ugly one line,
them maybe it should be broken into multiple lines
for display too.
Only strings which contain a newline can be broken
into multiple lines:
"It is OK to\n"
"break this string\n"
Signed-off-by: NeilBrown <neilb@suse.de>
make dprintf() print program name and __func__, so that
this messaging is consistent.
Also remove all __func__ messages from pr_err(). We shouldn't
leak that internal data in error message.
If we really want function name there, we new pr_XXX might
be wanted.
Signed-off-by: NeilBrown <neilb@suse.de>
Sometimes mdadm prints messages with wrong name "mdmon",
and vice versa.
This patch solves this problem by changing method of determining
process name.
Now "Name" will be set in const at start of a program,
previously was hardcoded as #define.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch fixes 2 problems introduced by commit 9a518d8: not closing a
file descriptor and ignoring container devices. Array state is always
"inactive" for containers, so we make sure that the device is not a
container by reading also the "level" sysfs entry.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Reviewed-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The output of "mdadm --detail --export" isn't quoted properly so
fields that contain spaces can be a problem.
We only want the MD_UUID field, and it has a very well defined
format with no spaces.
So use 'grep' to limit the output to just that.
Signed-off-by: NeilBrown <neilb@suse.de>
Migration record is not always cleared after successful migration. This can
block another reshape from being started. Migration will not be continued via
systemd service due to error in verifying reshape position. This patch added
clearing migration record when disk is added to container, and after successful
migration.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The division
1<<20 / 200
is not exact, so dividing by this to convert bytes into half-megs
is wrong and results in incorrect output.
As we are doing "long long" arithmetic, there is no risk of an overflow
until we reach 64 petabytes.
So change to
* 200 / (1<<20).
Reported-by: Jan Echternach <jan@goneko.de>
Resolved-debian-bug: 763917
URL: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=763917
Signed-off-by: NeilBrown <neilb@suse.de>
Commit a821c95f11
besides introducing additional message, also changed
direct return to "goto" instruction.
'goto release' will cause routine to return with '-1',
when previously '1' was returned.
Described behaviour breaks e.g. IMSM reshape process.
This patch fixes this issue by changing 'goto' to proper one -
the one that returns '1'.
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Opening a block-special-device for an array that doesn't
exist causes that array to be instantiated (as an empty array).
Races at array shutdown can cause the array to spontaneously
re-appear if some deamon notices a 'change' event and goes
to investigate.
Teach "mdadm --monitor" to avoid this race by checking the
"array_state" before opening the device.
Reported-by: Francis Moreau <francis.moro@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
check_rundir always needs to be "built", so making
mdadm and mdmon depend on it causes them to always be built.
i.e. running
make ; make
will needlessly link the binaries a second time.
So change the makefile to use "order-only" pre-requisites.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown
Andrew Burgess
Sergey Vidishev
Martin Wilck
Pawel Baldysiak
Artur Paszkiewicz
Jes Sorensen